09 630 0677 dsmteden@xtra.co.nz

415 Dominion Road, Mt Eden, Auckland 1024



$2,100.00 $1,699.00

1 in stock



Power 12″ T0 2-Ohm DVC Subwoofer

The T0D212 subwoofer mimics its performance and design from our older Power Series brothers. Our T0 12” features dual 2-Ohm voice coils, 700 Watts RMS power handling, and includes a grille with integral trim ring.

  • Anodized aluminum heat sinking dust cap
  • Anodized aluminum voice coil former
  • High-temp voice coil with spun-laced Nomex® re-inforcement collar
  • Kevlar fiber reinforced paper cone
  • Optimized and matched magnetic and compliance geometry
  • Optimized pole piece and spider venting
  • Periodic-stitched fatigue resistant tinsel lead wire
  • Proprietary 8 AWG insulated all metal input spring terminal connection
  • Rigid die-cast aluminum basket
  • T0D212

    The T0D212 12″ 2-ohm Dual Voice Coil subwoofer mimics the performance and design from its older Power Series brothers. The T0 subwoofers feature VAST technology that increases surface cone area up to 25% so it performs like a much larger woofer. The Flex Fit basket not only looks the part but it provides extreme flexibility for extreme installations. Clean, high tech, and high power handling characteristics let this subwoofer wear the torture-tested “Power Series” badge!

CEA-2031 Compliant: CEA-2031 Guidelines

Size: 12″

Subwoofer Type: Shallow

Power Handling (Watts RMS): 700 Watts RMS
1400 Watts Max

Nominal Impedance: Dual 2-Ohm

Voice Coil Type: Dual Voice Coil

Voice Coil Diameter: 3″ (75.5 mm)

Magnet Weight (oz): 106 oz. (3.00 Kg)

Speaker Connector: Compression Terminal

Fs (Hz): 25.3

Re (Ohms): 3.50

Le (mH): 5.34

Qms: 6.50

Qes: 0.51

Qts: 0.47

Vas (Liters): 55

Sd (cm2): 548

SPL (dB @ 1w/1m): 84.3

Xmax (mm): 14

Sealed Box Volume (Vb): 1.25 cu. ft. (35.3 Liters)

Vented Box Volume (Vb): 1.75 cu. ft. (49.5 Liters)

Woofer Displacement: 0.106 cu. ft. (3.0 Liters)

Cutout Diameter: 11.25 in. (285 mm)

Mounting Depth: 6.875 in. (174.6 mm)



Power 500 Watt Class BD Constant Power Amplifier

The Power T500-1bdCP is a 500 Watt mono amplifier featuring Constant Power delivering up to 25% more power across all impedance loads. The frequency response of the T500-1bdCP is optimized exclusively for use with subwoofers.

  • 24dB/octave crossover
  • MOSFET power supply
  • MOSFET output stage
  • 4 Gauge power/ground connectors
  • Audiophile grade speaker connections
  • RCA pass-thru outputs
  • Infrasonic filter


  • T500-1bdCP

    The T500-1bdCP is based on the legendary T500-1bd amplifier design with a proprietary “Constant Power” configuration delivering up to 25% more power (Watts) across all impedance loads. The listening experience is cleaner, louder and more impressive than ever before. With the T500-1bdCP, you can now use an “under-the-seat” dedicated subwoofer amplifier to drive two 4-Ohm DVC subwoofers. This amp will provide enough bass to separate you from those envious car audio geeks.

CEA-2006 Compliant: CEA-2006 Power Rating
300W x 1 @ 4Ω
≤1.0% THD+N

Number of Channels: 1

Rated Power
(RMS Continuous Power):
300 Watts x 1 @ 4-Ohm
500 Watts x 1 @ 2-Ohm
500 Watts x 1 @ 1-Ohm

Total Power
(Sum of Rated Power):
500 Watts RMS

Dynamic Power
328 Watts x 1 @ 4-Ohms
537 Watts x 1 @ 2-Ohms
707 Watts x 1 @ 1-Ohm

Bridgeable: No

Frequency Response: 20Hz to 250Hz +/- 0.5dB

Efficiency (average): 86.2% @ 4-Ohm
82.3% @ 2-Ohm
73.4% @ 1-Ohm

Total Harmonic Distortion (THD+Noise): 4-Ohm: <1.0%
2-Ohm: <1.0%
1-Ohm: <1.0%

Signal-to-Noise (CEA): >89 dB

Channel Separation:

Common Mode Rejection: >68 dB

Damping Factor: >200

Crossover Controls: Low-Pass (LP): 35-250Hz 24dB/Octave Butterworth
Infrasonic Filter: -3dB @ 28Hz 12dB/Octave

Tone Controls: Bass: 0dB to +18dB @ 45Hz

Input Sensitivity: 150 mV to 4 V

Signal Input: Low level: 1 RCA pair

Signal Output: Low Level: 1 RCA pair

Power Input Connector: Block

Power Wire Gauge: 4 AWG

Speaker Output Connector: Screw terminal barrier strip

Speaker Wire Gauge: 8 AWG to 18 AWG

Heat Sink Type: Cast aluminum

Cooling: Convection

Remote Controls: Optional Remote Punch Bass EQ
(overrides built-in Punch Bass EQ)

Visual Indicators: Power

Circuit Topology Class: Class BD

Operating Voltage: 9 – 16 VDC

Recommended Fuse
(not included):
80 A

Max. Current Draw (13.8V Sinewave): 70 A

Average Current Draw (13.8V Music): 35 A

Suggested Alternator: 75 A

Dimensions (H x W x D): 2.14 x 8.14 x 11.41 (in)
5.42 x 20.68 x 28.97 (cm)

Dimensional Diagram:

Additional information

Weight 17.00 kg